In-Box Review
Boeing 787-9
  • move

by: Is a secret [ JESSIE_C ]

Boeing's 787 was designed to replace the 767 and to compete with Airbus' A350 series. The 787 had a very prolonged test cycle, with production deliveries at least 2 years behind schedule. The schedule slip resulted from Boeing's extensive use of composite materials in the airframe instead of the traditional aluminium. Never before had so much of any commercial aircraft been constructed from non-traditional materials and the engineering challenges have been immense. The 787-9 is lengthened by 6.1 m over the basic 787-8 model, with seating for up to 280 passengers. Zvezda issued this kit in 2016.

First Impressions
Crisp and clean. Very little flash, few sink marks. Fine scribed lines that are out of scale for 1/144 but will still look good under a coat of paint. Panel lines match up very nicely. The plastic has Zvezda's trademark slightly pebbly texture which can be polished out, but which will disappear under the primer paint. The parts are nearly identical to Zvezda's previous 787-8 kit; only the longer fuselage differs. The kit also contains Zvezda's now traditional stand.

The fuselage is two halves from nose to tail. The cabin windows are open, with clear parts provided for them. The cockpit windows are the old-fashioned Airfix style strip, which makes getting them to fit properly without either breaking or falling into the fuselage something of a challenge. The panel lines are nicely engraved and match up well. The APU exhaust is left open, which means that one may look right through the fuselage and out the cockpit windows. It should be filled with a small blocked off piece of tube to prevent the see-through effect. If the windows are left open, the interior should be painted black to prevent the model from looking toy-like. There is no cockpit bulkhead to help confine the nose weight. The nose gear well and one piece of the nose gear support strut must be inserted before the fuselage is closed.

The wings have a one piece lower half with two uppers. The trailing edge of the flaps is moulded into the uper wing halves. They will need a little work to ensure that there is not a step in the surface of the flaps. The flap hinge fairings are moulded into the lower wing. There is no detail in the wheel wells.

The tailplanes are two piece mouldings that have two very small stubs as mounting surfaces. They may benefit from drilling out and replacing them with pins. Leave them off until final assembly to facilitate decalling. The elevator is moulded into the upper surface which leaves a bit of a gap to be filled.

The engines are beautiful little models in their own right. They have a two piece interlocking fan section with extremely delicate blades that mounts into a duct which is trapped between the cowl halves. The hot section is equally nicely detailed, then the intake section mounts onto the front of the cowl, and the characteristic sawtooth rear cowl section slides on over the hot section. These engines will look stunning when completed.

Landing gear
The landing gear struts and wheels are finely moulded and nicely detailed. The main struts have brake drum detail which mounts onto the struts before the wheels are installed. The nose strut has separate shimmy dampers and landing lights. They could use some brake lines and whatever else the modeller likes, but will look good without. The wheels themselves are properly thick and the detail moulded into the hubs is very good.There is an option for raised gear, and a stand is provided. As with all 1/144 kits, the gear doors are overly thick and may be replaced if the modeller wishes although Zvezda made an effort to get the edges thin.

I don't compare models to drawings or published measurements. When assembled it looks like a 787

Decals and markings
The decal sheet is in Zvezda's new glossy finish. There is one option for the Boeing prototype in the “Dreamliner” scheme. None of the fine white pinstriping is provided for the Boeing scheme. No window decals are provided. There are several different aftermarket sheets available to provide the airline scheme of your choice.

The kit may be cut back to the original 787-8 length if you don't have access to the earlier kit. It will also be possible to lengthen it to the forthcoming 787-10 variant by cutting 2 kits at the proper locations. It may also be possible to make a 787-8 from the leftovers.

Related Reviews
Aeroscale previously reviewed the 787-8 kit.
Highs: Delicate parts with a lot of detail for 1/144 scale.
Lows: Delicate parts mean that they can easily be broken or lost. Pebbly texture will make smooth paint schemes more difficult.
Verdict: This is the only 787-9 to get. It's a state of the art kit that will be a pleasure to build.
Percentage Rating
  Scale: 1:144
  Mfg. ID: 7021
  Suggested Retail: C$41.99
  PUBLISHED: Aug 01, 2016
  NATIONALITY: United States

Our Thanks to Zvezda!
This item was provided by them for the purpose of having it reviewed on this KitMaker Network site. If you would like your kit, book, or product reviewed, please contact us.

View Vendor Homepage  |  More Reviews  

About Is a secret (Jessie_C)

Copyright ©2021 text by Is a secret [ JESSIE_C ]. Images also by copyright holder unless otherwise noted. Opinions expressed are those of the author(s) and not necessarily those of AeroScale. All rights reserved.


Click image to enlarge
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move