ITALERI [ MORE REVIEWS ] [ WEBSITE ] [ NEW STORIES ]

In-Box Review
148
Bye-Bye Mirage F.1
Bye-Bye Mirage F.1
  • move

by: Kevin Brant [ SGTRAM ]

Introduction

Desgined in the 1960’s, the Dassault Mirage F.1 was built as a fighter/attack aircraft for the French Air Force. It entered service in 1974 and was retired in 2014 from the French Air Force, after 40 years of service. More then 720 Mirage F.1’s were built, with the primary users listed as France, Iraq, Greece, and Spain.

A new release from Italeri, a re-release with new markings, allows for building and marking up the F.1 during its final year.

Contents

4 Plastic Sprues
1 Sheet of Decals
Instruction Booklet

Review

From a quick view of this kit on Scalemate, it seems the history of the kits go back to an original release by Esci in 1978. It does look like this kit is a direct re-release of the Italeri 2012 release that contained new parts, with this release just including new decals. The kit is molded in grey plastic with engraved panel lines and some nice details. Although I did find some flash and sink marks, especially on the landing gear and some of the finer parts.

So as part of the review, I also started building this kit. Starting off with the cockpit, it is relatively plain, not a lot of details, but does include very rudimentary decals for the instrumentation. Also very little detail on the seat itself. I did throw a couple pieces of masking tape on to show some seatbelt details. For fit, it does go together relatively well.

Onto the fuselage, the fit of the cockpit and overall fit of the fuselage halves is not bad. There is some very minor warping, but nothing a little masking tape could not deal with while the glue dried. I did find that there as some major gaps in the back of the intakes when assemble, which does make it difficult to paint the interior before assembly. The instruction don’t state, but you will need to add some weight to the nose to keep the front landing gear down, and there is some room just ahead of the cockpit and if need be in the nose cone.

The instruction include steps to shave some detail off the tail fin and replace it with new parts, as the detail on those parts on the sprue did not look the greatest, I just left the molded detail on my build.

The wings go together pretty well, with instruction to drill a couple holes prior to assembly. The fit onto the fuselage is also pretty good, as well as the tail wings. Overall the entire fuselage goes together well, and was impressed with the “age” of the molds.

The drop tank and ordnance are not bad, but did find that the instructions had you put the wing tip sponsions onto the missiles prior to the aircraft, thinking this would make overall painting a little tough. Also the wing tip missile has big ejector marks and the fit of the winglets leave some gaps. I also found that the holes in the bottom fuselage for the center drop tank are jot completely lined up and a little small for the locator pins.

One issue I found was the canopy, whether it was warped or just not molded right, there is a fit issue. I did have to tape it down, so that the bottom “spreaded” a little to match the fuselage. As well I needed to sand the rear tab to fit into the slot, and it seems about half a millimeter to short.

As for the landing gear, there is flash and does almost seem the molds were not completely lined up. But this can be taken care with some sanding and scraping.

The decals are printed by Cartograph, so there should be not real issues there. You will need to take some care with the tail ones, as they are one piece and large. Painting and marking guide includes:

  • No. 611 French Air Force, EC 2-33 “Savoie” Mont de Marsan, June 2014
  • No. 653 French Air Force, EC 2-33 “Savoie” Mont de Marsan, June 2014
  • No. 660 French Air Force, EC 2-33 “Savoie” Mont de Marsan, June 2014


Conclusion

This re-release of the Mirage F.1 from Italeri is not really a bad kit, it does show the age of the molds in some spots. There as some poor fitting parts, for example the canopy and ordnance, as well as some flash and sink marks in some parts. The kits has decent fit in most places and will just need a little extra work and attention. The real highlight, and reason for the release, is the decal, printed by Cartograph and looking very nice.
SUMMARY
Highs: Decals, printed by Cartograph, look great, and overall fit decent
Lows: Showing age of molds, flash, sink marks, and some poor fit in some areas.
Verdict: Not a bad kit, will need some extra 'love and attention', in the hands of a skilled builder should be able to create a nice model.
  Scale: 1:48
  Mfg. ID: 2790
  PUBLISHED: Apr 17, 2020
  NATIONALITY: France
NETWORK-WIDE AVERAGE RATINGS
  THIS REVIEWER: 88.35%
  MAKER/PUBLISHER: 79.68%

Our Thanks to MRC!
This item was provided by them for the purpose of having it reviewed on this KitMaker Network site. If you would like your kit, book, or product reviewed, please contact us.

View Vendor Homepage  |  More Reviews  

About Kevin Brant (SgtRam)
FROM: ONTARIO, CANADA

I am an IT Consultant and father, with a passion for plastic models. I mostly prefer 1/35 Armor and 1/48 Aircraft. My main interests are anything Canadian, as well as WW2 German and British Armor and Aircraft. I have been building models since I was a young kid, got away from it for awhile, but r...

Copyright ©2021 text by Kevin Brant [ SGTRAM ]. Images also by copyright holder unless otherwise noted. Opinions expressed are those of the author(s) and not necessarily those of AeroScale. All rights reserved.



Comments

I do agree with Kevin. It's a nice topic, but the kit truly shows it's age. I had to do a lot of sanding, needed quite a lot of putty... well... somehow it will end in a nice, I hope so, finished model.
APR 17, 2020 - 01:25 AM
NeOmega offers a really nice resin cockpit set which will improve things massively.
APR 17, 2020 - 03:48 AM
If ever a subject was needed in 1/32, IMHO this is it! Of course as an all-injection kit. This would look totally awesome sitting next to the 1/32 Mirage III and Mirage 2000!
APR 17, 2020 - 04:15 AM
PLUS 1 to what Neil said.
APR 18, 2020 - 12:20 AM
   
ADVERTISEMENT


Photos
Click image to enlarge
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
ADVERTISEMENT