History

The Fokker D.VII became Germany’s main production fighter in 1918. Usually matched with the Mercedes D.IIIaü 180hp engine. It was the variant with the BMW IIIa 185 hp motor that pilots prized ultimately. With few idiosyncracies it was not temperamental and a novice with a little nerve could do well. Contemporary construction using welded metal tubing for the fuselage and wooden wing structures was typical. The secret appeared to be in the Cantilever boxed wing spars and the simple design that eliminated the need for multiple exposed rigging wires. For several reasons the Fokker D.VII is a must have item in the serious collector/modeler’s stable. The lack of rigging is a big plus, the various decal sheets of “cookie-cutter” lozenge, two toned streaked patterns, unit and pilot markings that are available in most scales. References on the subject are also at an all time high.

Kit Contents

#32030 1/32 Fokker D.VII (OAW) US$79.00
213 high quality injection moulded plastic parts.
22 exclusive parts to build aircraft made by the Ostdeutsche Albatros Werke in Schneidemühl.
08 photo-etched metal detail parts.
36 page fully illustrated instruction manual.
05 high quality Cartograf decal sheets with markings for 5 individual aircraft;

Instructions

This is the typical quality reference that we have come to expect from WNW kits. The graphics an high quality images give us a monograph that will become a permanent fixture in our reference libraries. The step by step guide is easy to follow in most cases. The captions for the build steps and reference photos give you a good understanding of the subject matter. But one must realize that some subjects are a bit of a guess. Colours are noted for every item in the build. Tamiya, Humbrol and Misterkit model paints are solid references.

The WNW Christmas 2012 line-up usually had some fine releases and it seems their most impressive yet. WNW has done three separate Fokker D.VII kit issues. One each for Fokker (Schwerin), Albatros (Johannistahl) and OAW (Schneidemühl) machines. Wingnut Wings has also offered four aftermarket decal sheets to go along with this festive introduction. With this article all kits have been reviewed here at Aeroscale.

This kit #32030 represents the OAW factory-built version and arrives in the WNW typically colourful top opening box, with the sprues, instructions, decals and accessories all individually bagged for protection. The moulding in the review kit is crisp, sharp, clean details and no flash. A close inspection with an optivisor showed a couple of minor sink marks on the underside of the fuselage and on the firewall and will prove easy to clean up. Ejector pin marks are well placed out of sight

The surfaces of the model have finely engraved panel lines, raised detailed fasteners and options for adding servicing ports. The louvres in the side cowling panels are depicted with open slots. The depiction of the fabric covering, in-scale rib tapes & underlying stitches on the wings and horizontal stabilizer. There is a very faintly "ballooned" effect on the undersides of the wings to depict the weight of the material on a machine at rest.

Aeroscale Managing editor Merlin has already noted (and it is worth repeating) a caution that “. . .many of the smaller parts are quite delicate, being moulded as close true-to-scale as possible yet their sprue-attachments are substantial to acheive the crisp level of detail. . .” I recommend using a cutting wheel in using a variable speed motor tool at low revs. to remove any parts to prevent damaging them.

The build

Page 1 First we start with the typical WNW general instructions & colour matches for paint. Note that there are several good decal sheets available now that replicate the contrasting wood grain.

Page 2 We find the parts maps.

Page 3 shows the maps for the six large and 2 errata decal sheets and the photoetch fret.

Step 1. The Cockpit.
The flooring (PP A 37) and rudder bar ( PP A 63) lateral pivot rod (PP A 57), control column (PP A 64) auxiliary throttles and the aileron control “vee” horns (PP A 11) come together. The rear cockpit screen (PP A 26) can be painted or decaled. But the decals would be used only if the whole fuselage was to be covered in lozenge. The pilot seat (PP A 38) is attached next with the supports (PP B 21 & 22) added next. Whether the seat was recovered at the front or not from the factory the seat back had eyelets for a fabric covering to be sewn in place. They were either plain or lozenge. As noted the pilot's seat cushion wasn't used if a parachute pack was employed.

The ammunition box (PP A 50 & 52 ) empty belt box (PP A 51 & 52 ), front gun mounts (PP A 2 ) Maximal fuel gauge (PP A 8), fuel tank (PP A 41 & 42). Now the fuel tanks spouts (PP A 58 & 60) need to be modified. Then the firewall (PP A 46) is next. The late Dan San Abbott mentioned that in his studies, metal firewalls were not installed in OAW types until about the Fok. D.VII (OAW) 6300/18. Originally 4635/18 had what appears to be a fabric screen instead of a metal firewall.

For those of you that are less familiar with the story, The hot summer months of 1918 manifested a problem with early Fokker D.VII types. Heat build up in the engine compartment and the lack of venting led to the premature cook off of the ammunition stores - in-flight. This concerned especially the phosphorous capped tracer rounds. The answer was better air induction to - and venting from the engine compartment.

The first unit to receive the new Fokker D.VII in late April/early May, 1918, was Jasta 10 of the elite Jagdgeschwader I. Their machines were marked with yellow engine cowlings. Ltn. Friedrichs was killed over Arcy at 20.45 hours in Fokker D.VII 309/18. The reason for the ammunition cooking off was attributed to the very hot summer weather and the lack of cooling vents / louvres. The addition of a “firewall” was an attempt to keep the engine heat away from the ammunition storage box. The guns were also raised. This difference is reflected in (PP A 2, 3) the forward gun supports.

Step 2. Cockpit continued.
Reflects alterations that can be done for the side frames (PP B 10 & 11) and the added equipment and the flooring assembly from step 1.

Step 3 Cockpit continued.
This step covers the instrument panel (PP A 40) and its equipment. High quality Cartograf decals for the instrument faces are high quality with clear small details. The final height of the guns was usually a determination that designated the engine as the BMW IIIa motor. It was a taller profile 11/16 of an inch. These profiles do not include the final raised positions.

Optinal altimeter (PP A 32 or 33) locations are discussed. In many cases smaller altimeters were worn on pilot’s wrists like a modern wrist watch. Though the faces were only slightly larger. Please note that the safety harness straps were in tended only to keep the pilot in the cockpit incase of erratic combat maneuvers. These narrow belts were made of a canvas.

Page 7 Is a very useful set of colour reference images of The Memorial Flight Association's BMW engined replica aircraft cockpit. Please note that WNW do caution against relying on the images too much as some details do not match original production machines.

Note! The inside of fuselage halves (PP B 19 & 13) of profile D (and maybe E ) are lined with a panel of reversed lozenge decal to represent the pattern showing through the rear of the fabric on the original. These appear lighter as the dye did not penetrate the fabric in a distinct manner. See also step 6.

Page 8 This is the general painting and rigging guide for all components assembled to this point. As usual the modeler must provide their own rigging material.

Step 4 Detailing the engine compartment.
Here we add the engine bearers (PP B 14 & 15) and their secondary supports (PP b 17). Commendably thin and an ingeniously designed as a single unit.

Step 5 Engine.
Wingnut Wings have used their typical “E” sprue for Mercedes D.IIIa 170-5hp, D.IIIaü 180hp / D.IIIav 200hp mouldings, as seen in the WNW Albatros D.V - Va, Pfalz D.XII kits. I recommend solder and brass wire / rod for the plumbing & wires. The red rings around the cylinder water jackets are a direct factory reference to the pistons being domed high compression types. Daimler Mercedes D.IIIaü 180hp (rated between 180hp - 200hp). On their Mercedes D. IIIaü 180hp six cylinder inline engine WNW uses ( PP E 4, 8, 11-22, 25-28, 30-33, 36, 42 & 43). Daimler Mercedes D.IIIaü 180hp and were generally known by the company as F 1466a. The aircraft engine cylinders are covered by water jackets these are the color of black/blued gun metal. The kit includes the oil filler tubes / vent caps (PP E 17 & 18), oil cycling tube (E 30) and the sparkplug wire conduit tubes (PP E 11 & 15) for both side views of the engine. The water feed line (PP E 42) to the jacketed intake manifold (PP E 33). Captured examples of this motor have labeled it a 200hp type due to the differences between German and British ratings for horsepower.

What you do get in the kit is the water line tubes (sending and receiving) from the water pump to the radiator. You need the oil sending tubes for the resevoir tank and upper & lower casing. This was located on the pilot’s right side of the engine midway and is to be flanked by two flanges. But again you can add these from solder. Note the carburetor set up (E 22) and its orientation. In 1918 the Mercedes D.IIIaü 180hp became the standard engine for Fokker D.VII fighters. Many, many Mercedes D. III and IIIa type motors were rebuilt to the D.IIIaü 180hp specifications at the airparks and the main rebuilding facility as the war progressed. That is why some captured examples had motors with the i.d. designation of D.III 160hp cast into their crankcases. This has caused the misconception that the standard 160hp and 170 hp were used in 1918 at a time when they had become obsolete. Often these were referred to as “160hp over compressed engines”. On the Mercedes D. type motors the decompression lever (PP E 12) was at the top of the tower (PP E 26) and employed during engine maintenance & repair. The handle was wood and could be unscrewed. The crank cases that had the generator shelf were normally for wireless equipped machines or heating unit. Only one Fokker D.VII is known to have had a wireless, yet the shelf as a standard option and appears to have been added regardless of airframe application.

Page 11.
Mercedes D.IIIaü 180hp with a thick type standup air pump before restoration.

Page 12.
Mercedes D.IIIaü 200hp with a dual horizontal type air pump after restoration. Captured examples of the Mercedes D.IIIaü 180hp motor have labeled it a 200hp type due to the differences between German and British ratings for horsepower. The horizontal dual pump (E 37) came into use in March of 1918. Add fine wire painted black or white to make spark plug wires.

Step 6. Fuselage.
Note! The inside of fuselage halves (PP B 19 & 13) of A-E are lined with a panel of reversed lozenge decal to represent the pattern showing through the rear of the fabric on the original. These appear lighter as the dye did not penetrate the fabric in a distinct manner. See also step 6. Next we add the sub assemblies to the fuselage halves (PP B 9 & 13) and unite them. WNW recommends sealing the fuselage spine joint first. Aeroscale Managing Editor advises it does no harm to reinforce this seam with a strip of stock sheet plastic inside the fuselage to overlap the edges. I strongly agree.

A choice of radiators (PP A 35 or 36 ), water fillet tubes (PP A 19 or 31), inset faces (PP A 44 or 45 ) and chin cowls should match the radiator you use. OAW designers saw a need to create a drain access so the radiator with the plain narrower center section (PP A 44) gave way to the one with the open slots in the center section (PP A 36) these were to access water plumbing petcocks.

Step 7. Cockpit forward deck & guns.
Two options are given for the top decking (PP H 1) ahead of the cockpit, There are no small muzzleflash plates present in this kit.

The pair of LMG 08/15 "Spandau Maxims"(PP D 13 X 2, D 1 X 2) can be attached to alternative "mid" or "low" mounts and are provided in all plastic or you can further detail them with photo etched fretted cooling jackets and sights. The windscreens (PP C 1 or 2 ) should be added last in my opinion. Locations for the separate oil tank (PP A 6 & B 2), empty belt tubes (PP A 12 & 13), fairing (PP A 61) for the fuel gauge (from step 1) and the Oigee optical gun site (PP A 65) are discussed. By the way the cocking handles (D 1 X 2) are not on the rear quarter views of D.4523/18 profile B on page 24 (Fuselage band blank). But they appear to be installed later in the image on p.25 with “Li” on the fuselage band. Since A. Fokker held stock interests in OAW its not surprising that the cocking handles wound up being “purchased”. Note also the images on pages 33 & 34. The late model has them where the early model does not.

Step 8 Engine cowlings.
Three types of engine cowling panels are provided. Two are versions for the early (PP J 2, 3, 4, 5, 16, 17 ) and one set for the later (PP J 6, 7, 18 & 21). All appear to be for profiles with the high mounted exhaust (PP B 7 & 25 ). The side panel set up for profiles B & E appear to be the same.

Step 9 Engine cowlings continued.
WNW has detailed their exhausts with weld-seams. One note if you have missed this you will find the radiator half shell is actually moulded to the pilot’s right upper engine cowling (PP J 9 & 22 ). Often this small plate was retained on the radiator shell when the upper engine cowlings were removed for summer / fall operations. The later production cowling (PP J 14) provides a flat shelf under the exhaust but deletes of course the small half shell.

Step 10 Under carriage & bottom wings.
The lower wings (PP H 3, 4 & 5) appears adequate for the application Though I wish the spars had run a bit deeper into the lower wing shells. Not just for the added stability, but if you wanted to do a bit of battle damage it would make it easier. This is not a flaw mind you. Just my opinion.

The undercarriage assembly has a very stout axle (PP A 30) which, as it does on the original also serves as the mounting for the struts. The OAW wing axle (PP J 8 & 12 ) was designed as removeable. The wheels (PP D 8 X 2) are detailed with raised letters on the tires and air valves visible behind the separate outer covers (PP D 3 X 2).

Step 11 Tailplane.
The horizontal stabilizer (PP H 2), elevator (PP H 6, D 17 X 2), fin (PP A 56) and rudder (PP A 21, D 17) braces (PP B 23 & 24) Tail skid (PP A 10) and lifting handles (PP D 14 X 2) are all added here.

Step 12 Wings and Cabane struts.
Note the tripod forward cabane struts (PP B 8 & 12) were welded together at their high apex and to help you with that WNW has them as one moulded unit for each side. The “N” shaped wing struts (PP D 2 X 2) are commendably thin & in-scale.

As an addition the flash guard tubes (PP D 7 X 2) (PE 3) in my opinion were seen on machines after the problems with the engine compartment over heating issue in the summer months of 1918. This was another measure that was meant to keep tracer rounds from igniting any fuel or oil fumes.

Step 13 Top wing & final assembly.
Finely moulded Heine (PP E 1), Axial (PP E 24) and Neindorf (PP E 46) propellers are specified for use in the colour schemes provided . Note the instructions say that they were often replaced with different types in service, so some latitude if you so chose. If you are modeling the aircraft from a specific reference it is good to follow that.

WNW has made attaching the upper wing an easy affair. The main "N" strut slots may have to be opened but dry fit before committing glue. As on the original aircraft, it is the cabane struts that do the load-carrying, with pretty substantial lugs supporting the wing. The forward tripod struts (PP B 8 & 12) are moulded as one unit and should make it easy.

Page 22 Rigging diagram.
The attraction for most modelers is the lack of rigging on the Fokker D.VII. A pair of cables run from the fin to the horizontal tail, another pair brace the undercarriage, then there are control cables to add for the ailerons, elevator and rudders. That's it. The instructions include a rigging diagram showing the aircraft from two angles. Note the colours blue and green. Those listed as optional were usually fitted in the field and standardized on later production airframes.

Decals

A. Fokker D.VII (OAW) 4198/18, Jasta 60, Ltn.d.R. Karl Waldemar Ritscherle served in FEA 2, Schusta 8 & Jasta 60. He came to Jasta 60 from JastaSchule I on 22 June 1918 and served to EOW. ( 8 victories ). He survived the war but was KIA on 24 August 1940, when Major Ritscherle's Heinkel 111 was shot down and crashed into Abberton Reservoir.
B. Fokker D.VII (OAW) 4523/18, Rudolf Stark, Jasta 35b, late 1918 (11 Victories). While showing some forethought consider that Stark’s D.4523/17 scheme was NOT completed in a short period of time. Having the lilac painted locations not completely match, may be more accurate.
C. Fokker D.VII (OAW), Franz Büchner, Jasta 13, October- November 1918 (40 victories). This late model OAW built machine is seen after the war wingless and without its horizontal or vertical tail units. Its blue seemed much lighter than other images of Jasta 13 examples that are available.
D. Fokker D.VII (OAW), Willhelm Leusch, Jasta 19, October 1918 (5 victories). The command of Jasta 19 was given to Ltn. des Res. Wilhelm Leusch on 18 October 1918. He led Jasta 19 until the end of the war, while the unit was based in Trier. Leusch personalized his aircraft from the D.6300 to 6649/18 production batch with beautifully depicted dragon. The typical paint scheme of Jasta 19 markings, was the yellow nose, blue rear fuselage (the blue was the Jagdgeschwader II marking). This machine was later photographed in French hands post war.
E Fokker D.VII (OAW), Ltn.des Res. Ulrich Neckel, Jasta 6, September-November 1918 (30 Victories). He came from Jasta 19 on 1 Sept. 1918 and served there til EOW. He had a long career. He served in FA 25 and by 8 Sept.1917 was serving in Jasta 12 of JG II as a private. His award of the “Orden Pour le Merite” was the penultimate issue. He died in Northern Italy of tuberculosis at the age of 30 on 11 May 1928.

Pages 31-33. Good studies shots of various Fok. D.VII (OAW) built. The bottom two images on page 31 are from the Lafayette Foundation and were first published in the 1997 Albatros Ltd. publication Anthology 1.

Decals

Five large sheets! Cartograf, registration is as close to "painted on" as you will see in waterslide decals. It is impressive is the way overlapping markings are grouped as single decals. This is something we have seen on other Carograf sheets and seems to be one of their hallmarks.

Three of the sheets are devoted to lozenge decals, with both 4 and 5 colour patterns. in "cookie cutter" types to make for simpler application. A nice addition is patches of each colour for spot repairs. The colours of the lozenge camouflage decal have been dealt with in past reviews here at Aeroscale and it can be said that they are still good overall and I would include texturing even as they themselves have allowed to be done on their display models.

Production serials of the Fok. D.VII built by Ost Albatros Werke

Fok.D.VII(OAW) 2000 to 2199/18.
Fok.D.VII(OAW) 4000 to 4199/18.
Fok.D.VII(OAW) 4450 to 4649/18.
Fok.D.VII(OAW) 6300 to 6649/18.
Fok.D.VII(OAW) 8300 to 8649/18. Delivered after the war.

References

Combat Colours #14 The Fokker D.VII by P. Cooksley, Airfix Magazine. Date unknown.
Details & Colours Windsock Intl. Vol.3 #3 Summer 1987.
Fliegertruppen #2 by A.Ferko, Privately Published, Salem Ohio, 1987. (photocopies may be obtained by contacting the University of Texas at Dallas through the special aviation collection.)
Flight Report Cross & Cockade Great Britain, Vol. 2 # 4.
Fokker D. VII Aces of WWI, pt. I by Franks & Van Wyngarden. Osprey pub. 2003.
Fokker D. VII Aces of WWI, pt. II by Franks & Van Wyngarden. Osprey pub. 2004.
Fokker D.VII by Egon Kreuger, Profile Pub. Ltd. 1962.
Fokker D.VII by P. Grosz, Albatros Pub. Ltd, Datafile #9. 1989, 1993, & 1994.
Fokker D.VII Anthology 1 by R.Rimell, Albatros Pub. Ltd. 1997.
Fokker D.VII Anthology 2 by R.Rimell, Albatros Pub. Ltd. 2000.
Fokker D.VII Anthology 3 by R.Rimell, Albatros Pub. Ltd. 2002.
Fokker D.VII Kit Survey by R.Rimell, Albatros Ltd. Windsock Vol 13, #4 1997.
Fokker D.VII Covering Practices by Dan-San Abbott, WWI Aero #102, Pp.22-33. 1984.
Fokker D.VII Detail Marking and Finish of Fokker-built D.VII Aircraft by Dan San Abbott, WWI Aero #107, 1985.
Fokker Fighters of WWI by A. Imrie, Osprey, Vintage Warbirds #6 Pp.41-64 1986..
Fokker’s Last Deadly Scourge by M. O’Leary, Air Combat, Pp. 18-26. 1975.
Forgotten Fokker by P Cooksley, Cross & Cockade GB Vol.4, #2,Pp.84-86. 1973.
That Fokker’s an Albatros! By Wally Tripp, WWI Aero, #102 , Pp.14-21. 1984.
Udets Fokker D.VII Fighters by Dan-San Abbott, Windsock Vol.4, Spring 1989.
German Army Air Service in WWI by R.Rimell, Osprey, Vintage Warbirds #2, Photos 42-44, 1985
Germany’s Last Knight of the Air by C. Degelow, William Kimber Pub. London, 1979.
Wings of War by R. Stark, Arms & Armour Press. 1973.

When contacting retailers or manufacturers, please remember to mention that you saw their products highlighted in review here on Aeroscale.